Graphic Wraps - scroll to bottom for photo gallery

DVC Graphics can graphic wrap just about anything! With our large-format printing technologies using solvent based inks and 3M™ ControlTac and Over-laminates we can create unique wraps with long lasting qualities.

What is a Vehicle Wrap:
A Wrap is a large vinyl decal. It is applied directly over the original paint of the vehicle. The application of the Wrap allows you to change the car’s appearance in a very short period of time and in turn allows you to remove the Wrap, returning the vehicle back to it’s original condition in an even a shorter period of time, if it’s necessary!

The DVC Graphics' alternative to paint is not only more cost effective, but will provide more pop, detail and impact that paint cannot come close to. Whether you are a large corporation, advertising for a weekend, a company advertising your business for a few years or an individual that has a custom DVC wrap created for your daily driver. A DVC wrap will get you noticed!

The High Performance vinyl used for a DVC wrap requires properly prepared surfaces to promote adhesion. On many vehicles, we will encounter painted surfaces that may not be conducive for that necessary adhesion and durability of the materials, such as door handles, hinges, textured surfaces, emblems, rubber, moldings, weather stripping, sliding windows, exhaust areas and some extreme convex and compound curves. There are techniques for handling some of those areas, such as providing overlays, patches, relief cuts and taking these areas of concern into consideration during the design phase prior to printing. The practice of using these techniques for blending and coverage makes those areas difficult or impossible to see from 5-10 feet away. It is important that you understand a wrap does not provide for covering 100% of the vehicle, as some areas are not conducive to vinyl at all such as cracks, expansion joints and seams. The material manufacturers recommend a º inch gap in these areas to prevent material failure and insure correct adhesion. The materials used by DVC Graphics are of the highest quality and have provisions designed for outdoor use, such as the utilization of inks and laminates with UV properties, to help prevent fading and cracking over time. The durability of these materials can range from 1 to 5 years depending upon the climate and you’re care of the wrap.

DVC Graphics can offer a corporate look, custom look or the wildest ideas you can come up with.

How does it look? If you have to touch it to see how we did it, we did a good job! It looks as good or better than a brand new car and it stays that way for up to 5 full years. One delivery van can offer more than 18 million visual impressions per year. Now you know why everyone is looking at you!

What else can you do? Just imagine your logo or identity everywhere. Trucks, trailers, snowmobiles, and vehicle fleets can all have the same corporate or graphic look to represent you or your product better than your competitors! It’s about presence, standing out in the crowd and getting noticed. It sells, supports and promotes to everyone who sees it.

Sled wraps

DVC Graphics is now wrapping snowmobiles for snocross racing. Our goal for sled wraps is to raise corporate interest and investment in a growing extreme sport. Sled wraps also create a team identity by making them stand out among competitors.

 How long does the custom process take? In most cases from 10-20 days.

 Will the material damage my paint? DVC Graphics uses only the finest High Performance Vinyl. This 3M material is designed to be removed without damaging the paint. However, you may want to be careful if you have an aftermarket non OEM(Original Equipment Manufacturer) paint job.

How long does it take for installation of a DVC Graphics wrap?
The application process is individual with every job. A full trailer wrap can take up to a week to install while a partial vehicle wrap or sled wrap could take as little as a few hours.

How much does a wrap cost?
Great question! Information from you is the key to a proper estimate and again every wrap is custom. Please contact us for pricing quotes.     www.info@airbrushit.com

What is the cost (6 parts):
· Design Time: This is the number that is variable as most clients want custom design and this requires very specialized attention to detail the average design can take as little as 5 hours to some of our most complicated taking 40 hours.
· Materials: This number is predicated upon the amount of gross square footage needed to accomplish virtually seamless coverage of the intended area of wrap.
· Setup: This number is the most stable and only occurs when a design file needs to be setup for print. This number will occur every time a file needs to be formatted for print.
· Print: Print costs are included in the material costs and again is predicated upon the gross square footage.
· Lamination: Is included in the material costs.
· Contour cut (plotter): This fee occurs when the graphics need to be precision cut to follow body panels. A partial DVC wrap would be an example that has a plotter fee.

................................................................................................................................................................................